Unistrut p2785 Beam Clamp
Unistrut P2785 - Beam Clamp
Unistrut P2785 - Beam Clamp

Unistrut

Unistrut P2785 - Beam Clamp

$5.00
Finish:Electrogalvanized
Order Size:Single Piece
Quantity:
U-Bolt Beam Clamp is designed with an adjustable height to be used with many Unistrut channels. This clamp has a High capacity for heavy load requirements and is easy to install.


Features:

  • Vertical Design Load: 1,000 lbs per clamp (2,000 lbs per pair). Must use in pairs.
  • Use with P1000, P1100, P3000, P3300, P3301, P4000, P4001, P4100 and P4101 channels
  • Vertical and horizontal load capacities
  • This series is available in Electrogalvanized (EG), Unistrut Defender (DF), Hot-Dip Galvanized (HG), and Stainless Steel (SS).

 

Design Loads

Design Load:  1,000 lbs (4.45 kN) each

Notes:

  1. Design loads only apply to Unistrut brand products. Look for "UNISTRUT" on the part.
  2. Use in pairs only.
  3. Safety factor = 2.5 based on ultimate strength of connection.
  4. For use with beam flanges up to 3/4" (19.1 mm) thick.
  5. Use with Channels P1000, P1100, P2000, P3000, P3300, P3301, P4000, P4001, P4100, and P4101.
Specifications

General Specifications

Standard Dimensions (Unless Shown Otherwise on Drawing):

  • Hole Diameter:  9/16"  (14mm)
  • Hole Spacing (From End):  13/16"  (21mm)
  • Hole Spacing (On-Center):  1 7/8"  (48mm)
  • Width:  1 5/8"  (41mm)
  • Thickness:
    • 1/4"  (6.4mm) with steel meeting or exceeding ASTM A1011 SS GR 33, or
    • 0.220" (5.6mm) with steel meeting or exceeding ASTM A1011 HSLAS GR 45

Note:

  • When used for mechanical supports, load capacities of brackets and fittings should be in compliance with the American Standard Code for Pressure Piping.


Materials & Finishes

Materials & Finishes - Standard:

  • Base Metal: Steel conforms to ASTM A1011 SS GR 33, A1011 HSLAS GR 45, A36, A575, A576, or A635.
  • Electrogalvanized (EG):  Conforms to ASTM B633, Type III SC1
  • Unistrut Defender (DF):  Conforms to ASTM A1059
  • Hot Dip Galvanized (HG):  Conforms to ASTM A123 or A153
  • Perma-Green (GR):  Conforms to commercial standards for powder coating
  • Perma-Gold (ZD):  Conforms to ASTM B633, Type II SC1 or SC3
  • Plain (PL):  No finish 

Materials & Finishes - Special Metals:

  • Stainless Steel, Type 304 (SS):  Conforms to ASTM A240 or A276, Type 304 *
  • Stainless Steel, Type 316 (ST):  Conforms to ASTM A240 or A276, Type 316 *
  • Aluminum (AL):  Conforms to ASTM B209, Type 1100F or 5052-H32 *

* These materials have different physical properties and performance characteristics. Please contact us for design support.

 Downloads

P2785 Cut Sheet